We tested Lian Li’s black version of the Lancool 217, outfitted with dark walnut trim; the company also offers a white version with beech accents for a $5-higher list price. We expect a case at the Lancool 217’s price to include a pair of intake fans and an exhaust fan, but Lian Li goes one better by equipping this model with an extra pair of fans mounted to the top of its power supply tunnel.
Lian Li continues its splurge by securing the corrugated mesh front panel with magnets and surrounding it in nicely finished wooden trim. Its designers also decided to secure its left-side tempered-glass panel with snaps at the top and tabs at the bottom. Plus, that side’s vented lower portion is removable, with sliding tabs along its length and a screw at the back.
The power button, on the top panel and metal-skinned, features a power-on indicator LED behind a small rectangular plastic diffuser. It looks striking.
(Credit: Thomas Soderstrom)
Oddly, a second power button is positioned in the classic “front panel” group along the front edge of the lower left side-panel. Positioned exclusively for people who like to be able to see inside their PC while they work or play (i.e., who have their tower on a desk or table), the group includes a headset combo (headphone plus microphone) jack, a pair of USB 3.x Type-A ports on a Gen 1 internal cable, and a Type-C port on a Gen 2×2 internal cable.
(Credit: Thomas Soderstrom)
A few features are hidden underneath the Lancool 217, such as the one-piece rear foot that conceals a rear-panel power jack, and three sets of slider slots for attaching Lian Li’s two internal drive cages (included) in various positions.
(Credit: Thomas Soderstrom)
Here’s a look at that power jack, along with the reason it’s located there: The power supply bay is designed to hold the power supply either longitudinally or transversely, and a cover plate is factory-installed to encourage transverse mounting. If you do the transverse mounting scheme, the power cable from the PSU gets fed from this rear port. Barely long enough to cover its air inlet, a power supply dust filter slides out the back of the case through a notch in its one-piece rear foot. Here you can see it partly removed.
(Credit: Thomas Soderstrom)
The rest of the rear panel features a removable expansion slot module that can rotate to support the vertical installation of a graphics card via a riser cable (not included). Also back here are four slots on a dual-pattern fan mount that allow a 140mm or 120mm rear fan to be installed at any height within the range of the motherboard’s I/O panel. A 140mm exhaust fan comes factory-mounted, and a notch near the top of each side panel makes it easier to pull these away from their upper-edge snaps.
A vent along the lower edge of the right side’s panel feeds air to the Lancool 217’s center fans and drive bays.
(Credit: Thomas Soderstrom)
Behind that right side panel is the below assortment of cables, cable grommets, drive trays, and mounting bays.
(Credit: Thomas Soderstrom)
Starting with the powered fan hub at the top of that opening, we can see that five of its six fan headers are factory-filled with included fans. That leaves just a single PWM header for adding another case fan, though you can certainly connect additional fans directly to headers on your motherboard or add splitter cables when the need arises.
(Credit: Thomas Soderstrom)
The four ARGB headers that are also present go unused, since the included fans aren’t lighted, and the case includes no other lighted accessories. Its 3-pin (5V) ARGB headers are protected by caps.
Below the motherboard tray and its two rear-mounted 2.5-inch drive trays, the lower bays feature room to mount two drive cages and the power supply. Also stowed there is the cable you’ll need to use if you transverse-mount the power supply, with its power jack hidden behind the opposite side panel. We measured 210mm of power-supply clearance cross-ways (despite Lian Li’s 180mm rating). Builders who need more space than that can get all the room they need by removing the rear cover plate, mounting their power unit lengthwise, and leaving out at least one of the separately packed lower drive cages.
(Credit: Thomas Soderstrom)
Though it’s part of the installation kit, we decided to show one of the add-in drive cages below to give you a better idea of how the above space can be used. Each cage contains a single drive tray that holds a 2.5-inch drive on the underside and a 3.5-inch drive on the top side. The lid of the cage is also designed to hold either a 2.5-inch or 3.5-inch drive using rubber grommets and shoulder screws to provide a vibration-damped snap-in interface.
(Credit: Thomas Soderstrom)
Moving a few cables out of the way also exposes the adjustment screw for the horizontal graphics-card support on the opposite side.
(Credit: Thomas Soderstrom)
Below we see the graphics-card support mentioned above. It’s a small tab located just above the forward fan of the center divider (i.e. the power supply tunnel). Also visible at lower left is the mounting flange for installing the power supply cross-ways, the rear fan hole cover that features a set of holes to allow a seventh (!) 2.5-inch drive to be mounted there, the outlet side of the two reverse-flow center fans, and a bunch of holes in the motherboard tray that were placed there to support motherboards with reverse-facing cable headers.
Get Our Best Stories!
All the Latest Tech, Tested by Our Experts
By clicking Sign Me Up, you confirm you are 16+ and agree to our Terms of Use and Privacy Policy.
Thanks for signing up!
Your subscription has been confirmed. Keep an eye on your inbox!
(Credit: Thomas Soderstrom)
Note that the reverse-connector passages are spaced for MSI Project Zero and Asus BTF MicroATX and ATX motherboards that have that feature, while the range of supported boards that don’t have that feature goes all the way down to Mini-ITX (which is to say, the smallest of ATX-based boards) and all the way up to SSI-EEB (the largest of EATX-labeled boards).
Lian Li is one of the few companies that has figured out how to make a rotatable card bracket that has its screw tabs on the inside of the case. In traditional builds, this allows your PCI Express cards to be inserted straight down into the slot, rather than tilting the card and finessing its bracket through a rear-panel hole.
(Credit: Thomas Soderstrom)
The Lancool 217’s top fan mount is removable. It fits up to three 120mm or two 140mm fans, and it leaves you enough space above the motherboard to hold a 406mm-long radiator with fans up to a combined 60mm thickness.
(Credit: Thomas Soderstrom)
The Lancool 217 front fans are an unusual oversize kind, at 170mm, and mounted without the airflow restriction of a multi-size bracket. That’s because Lian Li decided instead to include adapter brackets in its installation kit for those who would like to install a standard-size front-panel radiator. Radiators up to 457mm long and 38mm thick will fit behind the fan mounts.
(Credit: Thomas Soderstrom)
The factory 170mm fans can also be positioned slightly higher on the front panel by removing the top filler panel visible above, snapping the fans into their alternate mounting holes, and reinstalling both filler panels at the bottom of the opening. Below, you can see one of the filler panels removed near the case’s top.
(Credit: Thomas Soderstrom)
